]]>
]]>
]]>
]]>
]]>
]]>
]]>
]]>
]]>
Your post answered your question...
...it is ok to connect burn effect controller incoming power directly to the ASP2 smoke port, right?
"The burn effects battery voltage wires are NOT colour coded they are both black. This is the reason I do not suggest using the Smoke connector on Asp which is the easy way. "
I suggest that you DO NOT connect the Burn Effect direct to the smoke port.
And I thought I read about it in the past, but now can't find it anywhere..
It is on Page 2 of this very topic, your attached quote is on Page 3 - go back one more page
Cheers
KG
Statistics: Posted by Phyrephish — Thu Feb 16, 2017 8:28 am
]]>
]]>
I was just not sure about the wiring and didn't know about the pulse timing.
Thanks for explaining it to me, now i know the best way to get servo recoil.
Cheers
Steve
Statistics: Posted by Afrikakorps — Sat Jan 21, 2017 7:25 am
]]>
The H/L recoil is not a recoil system at all - just a modified airsoft system. The H/L recoil requires the controller to provide a long period of power to the motor. Real recoil requires only a short burst of power. With Asp the recoil motor connection also doubles as the LED flash connection so the pulse of power supplied is only short.
I would not waste any time with it. The servo mod takes less than 1 hour and costs less than $5. You will spend far more hours if you try to wire in the HL recoil
Cheers
KG
Statistics: Posted by Phyrephish — Fri Jan 20, 2017 10:29 am
]]>
I have another ASP2 and are not sure how to get the Heng Long recoil wired.
I know the HL recoil is not accurate, but at this stage it is better than none.
Two wires come from a small recoil motor ( not sure which is - or
+ ) and two wires from either side of a microswitch located at the back of the recoil.
I am thinking that from the recoil output on Asp2 , one wire goes to the + recoil motor, another (sig-) goes to the other side of the motor, and the third wire from asp recoil (VO) goes to the micro switch . From the other side of the microswitch the wire goes back to the neg side of the motor ( same side as the sig- ).
This is basically the same as the Taigen wiring.
Do you think this is correct ?
I don't want to do it half arsed
and connect up wires not knowing what the result will be.Thanks for your help, Cheers Afrikakorps.
Steve
Statistics: Posted by Afrikakorps — Fri Jan 20, 2017 8:24 am
]]>
Unless H/L have invented some magic that allows for the electronics to see into the future the only way to sync sound and projectile fire is via feedback. H/L's primary focus is airsoft and this is the overriding factor on their board design. This feedback is cheaply provided by the microswitch at the back of the airsoft/recoil unit. For IR or scale modellers this is always going to be flawed as the flash and sound will always come AFTER the recoil back is complete. To be as cheap as possible this is how the system works in the H/L electrics for BOTH airsoft and IR.
H/L System
Fire initiated - causes recoil or airsoft motos to wind up - airsoft motor reaches the limit and trips switch and fires projectile OR in IR - recoil motor snaps back and triggers microswitch. All the switch does is provide a temporary connection to ground (V-). When the controller registers this it initiates the sound and the nasty nasty track recoil.
HOWEVER, ASP is different in that there are 2 operating modes - Airsoft OR I/R
When set in Airsoft mode Asp acts similar to the H/L system and waits for the micro switch signal to trigger the sound and thus syncs with the firing of the projectile.
When set in I/R or realistic mode the sequence is correct. Initiate fire and the flash goes off, barrel recoil is triggered and the sound is activated. There is no need for feedback as we are not waiting for the airsoft pellet to be shot out. There is no need for the microswitch at all.
So I'll let you decide which system infact has minimal piss-farting around. The 5-6 wires needed for Asp or the Medusa like jumble of wires needed to hook up to the HL system
Cheers
KG
Statistics: Posted by Phyrephish — Mon Jan 16, 2017 6:54 am
]]>