| RC Tanks Australia Forum http://www.rctanksaustralia.com/forum/ | |
| M2A1 Bradley IFV http://www.rctanksaustralia.com/forum/viewtopic.php?f=111&t=1055 |
Page 3 of 3 |
| Author: | scalawag [ Tue Jan 05, 2016 12:38 am ] |
| Post subject: | Re: M2A1 Bradley IFV |
Next step, Light tan added to the camo, and some of the details begin to be added. Paul |
|
| Author: | scalawag [ Tue Jan 05, 2016 8:29 am ] |
| Post subject: | Re: M2A1 Bradley IFV |
The next Camo colour is now on. This is Tamiya NATO brown and will be the lighter of the 2 browns. Should have said previously that the light tan colour is Tamiya wooden deck tan. A few more little details added again. Paul |
|
| Author: | scalawag [ Tue Jan 05, 2016 4:48 pm ] |
| Post subject: | Re: M2A1 Bradley IFV |
On with the 4th camo colour, this is the darker brown which I used Tamiya flat brown for. Also some more details added, a little stubble added using very thinned down Tamiya german grey. The goggle lenses have a base coat of german grey too. Choc chips are next, hopefully get this done today. Paul |
|
| Author: | scalawag [ Tue Jan 05, 2016 9:31 pm ] |
| Post subject: | Re: M2A1 Bradley IFV |
The black elements of the choc chips are now added, flat black for these. Sorry for the dark pics, it is raining so hard here there is no natural light at the moment. Paul |
|
| Author: | scalawag [ Tue Jan 05, 2016 11:33 pm ] |
| Post subject: | Re: M2A1 Bradley IFV |
Choc chip camo is now complete. Final colour is flat white, used to finish off the choc chips. A light wash has been applied along uniform seems etc... using Mig dark wash. These have also now had a mat clear coat, but I took these pics before that went on. last steps will be a coat of Tamiya smoke for the goggle lenses, and a dust with some appropriate colours of Tamiyas weather master. next pics will probably be in place on the Bradley. Paul. |
|
| Author: | scalawag [ Wed Jan 06, 2016 8:18 am ] |
| Post subject: | Re: M2A1 Bradley IFV |
Here are the finished figures. The goggles have had the lenses painted with Tamiya smoke which has a dark tint and dries to a gloss finish. The whole figure has then been dusted with various Tamiya weather master colours to give a worn, dusty look. And some pics in place on the tank. As you can see the figure with the boonie hat can be used in the gunners hatch or the drivers. Hope you like them. Paul |
|
| Author: | scalawag [ Wed Feb 03, 2016 7:09 pm ] |
| Post subject: | Re: M2A1 Bradley IFV |
Hi Chaps, Just gotten round to adding the last bits of stowage on the M2A1 Bradley, which means this model is now complete. The new stowage pieces are from the Value Gear Generic Tarp Rolls & Crates Set #2. They are fantastic resin castings with a high level of very crisp detail. So here are some pics. This Model is a 21st Century toys die cast upper hull, on a modified Pzr III chassis, and Pzr IV running gear. IBU 2 Pro with custom sound set, which includes Tow Missile launch, bushmaster 25mm cannon and M240 Coax MG. From RC Tank Electronics. Audio amp from eBay. Viper remote volume control from RC tanks Australia. upgraded speaker from Tank Modellbau. Tarr 1 smoke unit from RC Tank Electronics. working head and rear lights. Figures from AFV models Stowage from various sources. Paint shceme is the original 21st Century one, which has been weathered using Mig washes and Tamiya Weather Master products. Additional painting and details where done using Tamiya acrylic paints. Videos of this tank can be found on my YouTube channel here https://www.youtube.com/channel/UCji0Th ... shelf_id=0 Paul |
|
| Page 3 of 3 | All times are UTC + 10 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ | |